OP-4-18V-24V-Q 9-36 V Input, 24 V/4 A Output Quarter-brick

OP-4-18V-24V-Q

OP-4-18V-24V-Q 9-36 V Input, 24 V/4 A Output Quarter-brick

Property

Value

Maximum Input Current (Max.)

15.7 A

Maximum Input Current (Notes & Conditions)

9 Vin min; trim up; in current limit

No-Load Input Current (enabled) (Typ.)

173 mA

No-Load Input Current (enabled) (Max.)

220 mA

Disabled Input Current (Typ.)

3.6 mA

Disabled Input Current (Max.)

5.0 mA

Response to Input Transient (Typ.)

0.7 V

Response to Input Transient (Notes & Conditions)

300 V/ms input transient; 100 uF output cap.

Input Terminal Ripple Current (Typ.)

350 mA

Input Terminal Ripple Current (Notes & Conditions)

RMS

Recommended Input Fuse (Max.)

30 A

Recommended Input Fuse (Notes & Conditions)

Fast acting fuse recommended

Output Voltage Set Point (Min.)

23.76 V

Output Voltage Set Point (Typ.)

24.00 V

Output Voltage Set Point (Max.)

24.24 V

Over Line (Typ.)

+/-0.1 %

Over Line (Max.)

+/-0.3 %

Over Load (Typ.)

+/-0.1 %

Over Load (Max.)

+/-0.3 %

Over Temperature (Min.)

-360 mV

Over Temperature (Max.)

360 mV

Total Output Voltage Range (Min.)

23.400 V

Total Output Voltage Range (Max.)

24.600 V

Total Output Voltage Range (Notes & Conditions)

Over sample, line, load, temperature & life

Peak-to-Peak (Typ.)

44 mV

Peak-to-Peak (Max.)

90 mV

Peak-to-Peak (Notes & Conditions)

Full load

RMS (Typ.)

11 mV

RMS (Max.)

20 mV

RMS (Notes & Conditions)

Full load

Operating Output Current Range (Min.)

0 A

Operating Output Current Range (Max.)

4 A

Operating Output Current Range (Notes & Conditions)

Subject to thermal derating

Output DC Current Limit Inception (Min.)

4.4 A

Output DC Current Limit Inception (Typ.)

4.8 A

Output DC Current Limit Inception (Max.)

5.2 A

Output DC Current Limit Inception (Notes & Conditions)

Output voltage 10 % Low

Output DC Current Limit Shutdown Voltage (Typ.)

14 V

Back-Drive Current Limit while Enabled (Typ.)

0.14 A

Back-Drive Current Limit while Enabled (Notes & Conditions)

Negative current drawn into output pins

Back-Drive Current Limit while Disabled (Min.)

0 mA

Back-Drive Current Limit while Disabled (Typ.)

15 mA

Back-Drive Current Limit while Disabled (Max.)

50 mA

Back-Drive Current Limit while Disabled (Notes & Conditions)

Negative current drawn into output pins

Maximum Output Capacitance (Max.)

400 uF

Maximum Output Capacitance (Notes & Conditions)

Vout nominal at full load (resistive load)

Settling Time (Typ.)

100 us

Settling Time (Notes & Conditions)

To within 1 % Vout nom

Output Voltage Trim Range (Min.)

-20 %

Output Voltage Trim Range (Max.)

10 %

Output Voltage Trim Range (Notes & Conditions)

Across Pins 8 & 4; Common Figures 3-5

Output Voltage Remote Sense Range (Max.)

10 %

Output Voltage Remote Sense Range (Notes & Conditions)

Across Pins 8 & 4

Output Over-Voltage Protection (Min.)

117 %

Output Over-Voltage Protection (Typ.)

122 %

Output Over-Voltage Protection (Max.)

127 %

Output Over-Voltage Protection (Notes & Conditions)

Over full temp range

Load Current Scale Factor (Typ.)

190

Load Current Scale Factor (Notes & Conditions)

See Output Load Current app. note on our web

100 % Load (Typ.)

89 %

100 % Load (Notes & Conditions)

See Figure 1 for efficiency curve

50 % Load (Typ.)

90 %

50 % Load (Notes & Conditions)

See Figure 1 for efficiency curve

Operating Input Voltage Range (Min.)

9 V

Operating Input Voltage Range (Typ.)

18 V

Operating Input Voltage Range (Max.)

36 V

Operating Input Voltage Range (Notes & Conditions)

40 V transient for 1 s

Turn-On Voltage Threshold (Min.)

10.0 V

Turn-On Voltage Threshold (Typ.)

10.3 V

Turn-On Voltage Threshold (Max.)

10.5 V

Turn-Off Voltage Threshold (Min.)

8.0 V

Turn-Off Voltage Threshold (Typ.)

8.3 V

Turn-Off Voltage Threshold (Max.)

8.6 V

Lockout Voltage Hysteresis (Typ.)

2 V

Recommended External Input Capacitance (Typ.)

470 uF

Recommended External Input Capacitance (Notes & Conditions)

Typical ESR 0.1-0.2 Ohm

Input Filter Component Values (LC) (Typ.)

0.4723 uH uF

Input Filter Component Values (LC) (Notes & Conditions)

Internal values

Non-Operating (Min.)

-1 V

Non-Operating (Max.)

40 V

Non-Operating (Notes & Conditions)

Continuous

Operating (Max.)

36 V

Operating (Notes & Conditions)

Continuous

Operating Transient (Max.)

40 V

Operating Transient (Notes & Conditions)

1 s transient, square wave

Isolation Voltage (Notes & Conditions)

Basic insulation

Input to Output (Max.)

2250 Vdc

Input to Baseplate (Max.)

2250 Vdc

Output to Baseplate (Max.)

2250 Vdc

Operating Temperature (Min.)

-40 °C

Operating Temperature (Max.)

100 °C

Operating Temperature (Notes & Conditions)

Baseplate temperature

Storage Temperature (Min.)

-45 °C

Storage Temperature (Max.)

125 °C

Voltage at ON/OFF input pin (Min.)

-2 V

Voltage at ON/OFF input pin (Max.)

18 V

Turn-On Time (Typ.)

9 ms

Turn-On Time (Notes & Conditions)

Full load, Vout = 90 % nom. (from enable)

Start-Up Inhibit Time (Min.)

180 ms

Start-Up Inhibit Time (Typ.)

200 ms

Start-Up Inhibit Time (Max.)

220 ms

Start-Up Inhibit Time (Notes & Conditions)

-40 °C to +125 °C; Figure E

Output Voltage Overshoot (Typ.)

0 %

Output Voltage Overshoot (Notes & Conditions)

Maximum Output Capacitance

Isolation Resistance (Typ.)

30 M Ohm

Isolation Capacitance (input to output) (Typ.)

1000 pF

Isolation Capacitance (input to output) (Notes & Conditions)

See Note 1

Semiconductor Junction Temperature (Max.)

125 °C

Semiconductor Junction Temperature (Notes & Conditions)

Package rated to 150 °C

PCB Temperature (Max.)

125 °C

PCB Temperature (Notes & Conditions)

UL rated max operating temp 130 °C

Transformer Temperature (Max.)

125 °C

Transformer Temperature (Notes & Conditions)

See Common Figure 3 for derating curve

Maximum Baseplate Temperature, Tb (Max.)

100 °C

Switching Frequency (Min.)

230 kHz

Switching Frequency (Typ.)

250 kHz

Switching Frequency (Max.)

270 kHz

Switching Frequency (Notes & Conditions)

Regulation and Isolation stages

Off-State Voltage (Min.)

2.4 V

Off-State Voltage (Max.)

18 V

On-State Voltage (Min.)

-2 V

On-State Voltage (Max.)

0.8 V

Pull-Up Voltage (Typ.)

5 V

Pull-Up Resistance (Typ.)

50 k Ohm

Over-Temperature Shutdown OTP Trip Point (Typ.)

125 °C

Over-Temperature Shutdown OTP Trip Point (Notes & Conditions)

Average PCB Temperature

Over-Temperature Shutdown Restart Hysteresis (Typ.)

10 °C

Calculated MTBF (Telcordia) TR-NWT-000332 (Typ.)

1.49 10^6 Hrs.

Calculated MTBF (Telcordia) TR-NWT-000332 (Notes & Conditions)

Tb = 70 °C

Calculated MTBF (MIL-217) MIL-HDBK-217F (Typ.)

1.31 10^6 Hrs.

Calculated MTBF (MIL-217) MIL-HDBK-217F (Notes & Conditions)

Tb = 70 °C

Step Change in Output Current (0.08 A/ us) (Typ.)

1200 mV

Step Change in Output Current (0.08 A/ us) (Notes & Conditions)

50 % to 75 % to 50 % Iout max

Features

High operational efficiency up to 91% with minimal power derating at full load.

Wide input voltage range of 9-36 V with 40 V transient capability and under-voltage lockout.

Industry-standard Quarter-brick form factor with an optional flanged baseplate for versatile mounting.

Fixed-frequency switching for predictable EMI performance and stable operation without minimum load requirements.

Enhanced control suite featuring remote sense, wide output voltage trim, and input-referenced On/Off control.

Robust integrated protection including output over-voltage, current limit, short-circuit, and thermal shutdown.

Fully certified to UL/CSA/EN 62368-1 safety standards and RoHS compliant.

Applications

Industrial and Transportation applications